How Can We Help?

HL-4G2 SFU Configuration [ZTE C6XX]

Created On
Last Updated On
byDaniel M
You are here:
< All Topics

HALNy HL-4G Configuration

Service Scenario

HL-4G2 can work in two modes – HGU (Home Gateway Unit) and SFU (Single Family Unit).
HGU mode configuration is presented here.
Managing ONT mode is done by setting up/or not bridge port and VEIP for ONT. In SFU mode we need to set bridge port and VEIP(only if we want to use ip-host).
SFU mode allows to prepare different configurations – such as QiQ tunnel or VLAN translation on the ONT. In this tutorial we will focus on SFU mode configuration.

ONT modes switching HGU<->SFU

Switching between HGU and SFU modes is described here.

Document Date and version2024.07.01
Tested on OLT ZTE C610Version: V1.2.2
Tested with ONT HALNy HL-4G2Supported on Version: V4.0.5 or above
Revision1
Let us know how to improve below document on: support@halny.com

Supported SFU service scenarios

1. ONT configuration (Access mode, only INTERNET)

This tutorial is based on ONT with firmware V4.0.5 and ZTE C610 running with firmware V1.2.2.

In example configuration we used below VLANs:
VLAN 100 – INTERNET
VLAN 400 – MGMT 

1. Create DBA profile

(config)# gpon
  profile tcont MAX type 4 maximum 102400

2. Create ONT Type
Change HL-MODEL string to exact model name of the ONT, ex. onu-type HL-4G2 gpon …

(config)# pon
  onu-type HL-4G2 gpon max-tcont 4 max-gemport 32 max-iphost 4
  onu-type-if HL-4G2 eth_0/1
  onu-type-if HL-4G2 eth_0/2
  onu-type-if HL-4G2 eth_0/3
  onu-type-if HL-4G2 eth_0/4

3. Register ONT on GPON

(config)# interface gpon-olt_1/3/3 
  onu 8 type HL-4G2 sn HALN323C3898

4. Configure ONT interface mode

(config)# interface gpon-onu_1/3/3:8 
  real-speed gpon
  vport-mode manual
  tcont 1 profile MAX
  tcont 2 profile MAX
  gemport 1 tcont 1
  gemport 2 tcont 2
  vport 1 map-type vlan
  vport 2 map-type vlan
  vport-map 1 1 vlan 100
  vport-map 2 2 vlan 400

5. Create vlan-profile (for IP host 1)

onu profile vlan tag400 tag-mode tag cvlan 400

6. Configure ONT remote management mode

(config)# pon-onu-mng gpon-onu_1/3/3:8
  service 1 gemport 1 vlan 100
  service 2 gemport 2 vlan 400
  wan-ip ipv4 mode dhcp vlan-profile tag400 host 1
  vlan port eth_0/1 mode hybrid def-vlan 100
  vlan port eth_0/2 mode hybrid def-vlan 100
  vlan port eth_0/3 mode hybrid def-vlan 100
  vlan port eth_0/4 mode hybrid def-vlan 100

7. Configure vports.

interface vport-1/3/3.8:1
  service-port 1 user-vlan 100 vlan 100
$
interface vport-1/3/3.8:2
  service-port 3 user-vlan 400 vlan 400

8. Verify ONT ip-host 1 IP address

#show gpon remote-onu ip-host gpon-onu_1/3/3:8
Host ID:            1
Host name:          IPHOST: WWW/XML/TR069
Identify:
IP addres:          0.0.0.0
Mask:               0.0.0.0
Gateway:            0.0.0.0
Primary DNS:        0.0.0.0
Second DNS:         0.0.0.0
DHCP enable:        disable
Ping response:      disable
Traceroute response:disable
MAC address:        54DB.A23C.3898
Current IP address: 172.17.60.13
Current mask:       255.255.254.0
Current gateway:    172.17.60.1
Current primary DNS:172.17.61.224
Current second DNS: 172.17.60.1
Domain name:

2. ONT configuration (Access mode, INTERNET + IPTV)

This tutorial is based on ONT with firmware V4.0.5 and ZTE C610 running with firmware V1.2.2.

In example configuration we used below VLANs:
VLAN 100 – INTERNET
VLAN 200 – IPTV
VLAN 400 – MGMT 

1. Create DBA profile

(config)# gpon
  profile tcont MAX type 4 maximum 102400

2. Create ONT Type
Change HL-MODEL string to exact model name of the ONT, ex. onu-type HL-4G2 gpon …

(config)# pon
  onu-type HL-4G2 gpon max-tcont 4 max-gemport 32 max-iphost 4
  onu-type-if HL-4G2 eth_0/1
  onu-type-if HL-4G2 eth_0/2
  onu-type-if HL-4G2 eth_0/3
  onu-type-if HL-4G2 eth_0/4

3. Register ONT on GPON

(config)# interface gpon-olt_1/3/3 
  onu 9 type HL-4G2 sn HALN323C3898

4. Configure ONT interface mode

(config)# interface gpon-onu_1/3/3:9 
  real-speed gpon
  vport-mode manual
  tcont 1 profile MAX
  tcont 2 profile MAX
  tcont 3 profile MAX
  gemport 1 tcont 1
  gemport 2 tcont 2
  gemport 3 tcont 3
  vport 1 map-type vlan
  vport 2 map-type vlan
  vport 3 map-type vlan
  vport-map 1 1 vlan 100
  vport-map 2 2 vlan 200
  vport-map 3 3 vlan 400

5. Create igmp profile

(config-gpon)#onu profile igmp 200 down-tag strip

6. Create vlan-profile (for IP host 1)

(config-gpon)#onu profile vlan tag400 tag-mode tag cvlan 400

7. Configure ONT remote management mode

(config)# pon-onu-mng gpon-onu_1/3/3:9
  mvlan 200
  service 1 gemport 1 vlan 100
  service 2 gemport 2 vlan 200
  service 3 gemport 3 vlan 400
  igmp eth_0/4 profile 200
  igmp eth_0/3 profile 200
  wan-ip ipv4 mode dhcp vlan-profile tag400 host 1
  vlan port eth_0/1 mode hybrid def-vlan 100
  vlan port eth_0/2 mode hybrid def-vlan 100
  vlan port eth_0/3 mode hybrid def-vlan 200
  vlan port eth_0/4 mode hybrid def-vlan 200

8. Configure vports.

(config)#interface vport-1/3/3.9:1
  service-port 1 user-vlan 100 vlan 100
$
(config)#interface vport-1/3/3.9:2
  service-port 2 user-vlan 200 vlan 200
  igmp fast-leave enable
  igmp version v2
$
(config)#interface vport-1/3/3.9:3
  service-port 3 user-vlan 400 vlan 400

9. Configure IGMP Snooping

(config)# igmp querygemport-mode both
(config)# igmp  mvlan 200
(config-igmp-mvlan-200)# source-port xxvgei-1/1/6
(config-igmp-mvlan-200)# receive-port vport-1/3/3.9:2
(config-igmp-mvlan-200)# host-version v2
(config-igmp-mvlan-200)# work-mode snooping

10. Verify ONT ip-host 1 IP address

#show gpon remote-onu ip-host gpon-onu_1/3/3:9
Host ID:            1
Host name:          IPHOST: WWW/XML/TR069
Identify:
IP addres:          0.0.0.0
Mask:               0.0.0.0
Gateway:            0.0.0.0
Primary DNS:        0.0.0.0
Second DNS:         0.0.0.0
DHCP enable:        disable
Ping response:      disable
Traceroute response:disable
MAC address:        54DB.A23C.3898
Current IP address: 172.17.60.13
Current mask:       255.255.254.0
Current gateway:    172.17.60.1
Current primary DNS:172.17.61.224
Current second DNS: 172.17.60.1
Domain name:

3. ONT configuration (Transparent mode)

This tutorial is based on ONT with firmware V4.0.5 and ZTE C610 running with firmware V1.2.2.

In example configuration we used below VLANs:
VLAN 100 – INTERNET
VLAN 200 – IPTV
VLAN 300 – VoIP
VLAN 400 – MGMT 

1. Create DBA profile

(config)# gpon
  profile tcont MAX type 4 maximum 102400

2. Create ONT Type
Change HL-MODEL string to exact model name of the ONT, ex. onu-type HL-4G2 gpon …

(config)# pon
  onu-type HL-4G2 gpon max-tcont 4 max-gemport 32 max-iphost 4
  onu-type-if HL-4G2 eth_0/1
  onu-type-if HL-4G2 eth_0/2
  onu-type-if HL-4G2 eth_0/3
  onu-type-if HL-4G2 eth_0/4

3. Register ONT on GPON

(config)# interface gpon-olt_1/3/3 
  onu 10 type HL-4G2 sn HALN323C3898

4. Configure ONT interface mode

(config)# interface gpon-onu_1/3/3:10 
  real-speed gpon
  vport-mode manual
  tcont 1 profile MAX
  tcont 2 profile MAX
  tcont 3 profile MAX
  tcont 4 profile MAX
  gemport 1 tcont 1
  gemport 2 tcont 2
  gemport 3 tcont 3
  gemport 4 tcont 4
  vport 1 map-type vlan
  vport 2 map-type vlan
  vport 3 map-type vlan
  vport 4 map-type vlan
  vport-map 1 1 vlan 100
  vport-map 2 2 vlan 200
  vport-map 3 3 vlan 300
  vport-map 4 4 vlan 400

5. Create igmp profile

(config-gpon)#onu profile igmp 200T down-tag transparent tag transparent

6. Create vlan-profile (for IP host 1)

(config-gpon)#onu profile vlan tag400 tag-mode tag cvlan 400

7. Configure ONT remote management mode

(config)# pon-onu-mng gpon-onu_1/3/3:10
  mvlan 200
  service 1 gemport 1 vlan 100
  service 2 gemport 2 vlan 200
  service 3 gemport 3 vlan 300
  service 4 gemport 4 vlan 400
  igmp eth_0/1 profile 200T
  igmp eth_0/2 profile 200T
  igmp eth_0/3 profile 200T
  igmp eth_0/4 profile 200T
  wan-ip ipv4 mode dhcp vlan-profile tag400 host 1
  vlan port eth_0/1 mode trunk
  vlan port eth_0/2 mode trunk
  vlan port eth_0/3 mode trunk
  vlan port eth_0/4 mode trunk
  vlan port eth_0/1 vlan 100,200,300
  vlan port eth_0/2 vlan 100,200,300
  vlan port eth_0/3 vlan 100,200,300
  vlan port eth_0/4 vlan 100,200,300

8. Configure vports.

(config)# interface vport-1/3/3.10:1
  service-port 1 user-vlan 100 vlan 100
$
(config)# interface vport-1/3/3.10:2
  service-port 2 user-vlan 200 vlan 200
  igmp fast-leave enable
  igmp version v2
$
(config)# interface vport-1/3/3.10:3
  service-port 3 user-vlan 300 vlan 300
$
(config)# interface vport-1/3/3.10:4
  service-port 4 user-vlan 400 vlan 400

9. Configure IGMP Snooping

(config)# igmp querygemport-mode both
(config)# igmp  mvlan 200
(config-igmp-mvlan-200)# source-port xxvgei-1/1/6
(config-igmp-mvlan-200)# receive-port vport-1/3/3.10:2
(config-igmp-mvlan-200)# host-version v2
(config-igmp-mvlan-200)# work-mode snooping

10. Verify ONT ip-host 1 IP address

#show gpon remote-onu ip-host gpon-onu_1/3/3:10
Host ID:            1
Host name:          IPHOST: WWW/XML/TR069
Identify:
IP addres:          0.0.0.0
Mask:               0.0.0.0
Gateway:            0.0.0.0
Primary DNS:        0.0.0.0
Second DNS:         0.0.0.0
DHCP enable:        disable
Ping response:      disable
Traceroute response:disable
MAC address:        54DB.A23C.3898
Current IP address: 172.17.60.13
Current mask:       255.255.254.0
Current gateway:    172.17.60.1
Current primary DNS:172.17.61.224
Current second DNS: 172.17.60.1
Domain name:

ONT HL-4G2 Provisioning on ZTE C610

There are two ways of ONT provisioning:

ONT HL-4G2 Upgrade on ZTE C610

Upgrade procedure is the same as for other HALNy ONTs (link)

Table of Contents
Hit enter to search or ESC to close

Search Page

The beauty of this theme is that is built with Modules. Every time you can active or dis-active any module that you would not need anymore ! Awesome WordPress Theme with latest technologies.

May We Suggest?