How Can We Help?

HALNy HL-4G SFU Configuration [NOKIA 7360]

Created On
Last Updated On
byMaciej K
You are here:
< All Topics

HALNy HL-4G Configuration

Service scenario

HL-4G can work in two modes – HGU (Home Gateway Unit) and SFU (Single Familly Unit).
HGU mode configuration is presented here and is similar to HL-4GMV.
Changing ONT mode is achieved by setting up/or not bridge port and VEIP for ONT. In example, if ONT has to be working as HGU, we need to set only VEIP. If as SFU, we need to set only bridge port(s).
SFU mode allows to prepare more complex configuration – such as QiQ tunnel or VLAN translation on the ONT. In this tutorial we will focus on SFU mode configuration.

ONT modes switching HGU<->SFU

ONT HL-4G supports auto mode switching with assigning according configuration. At this moment that function is supported on:

  • Dasan OLT
  • Zyxel OLT
  • Alcatel-Lucent/Nokia OLT

How to switch between SFU/HGU.

Supported SFU service scenario and ONT configuration

Document Date and version2020.06.01
Tested on OLT NOKIA 7360 FX-4Version: L6GPAA56.587
Tested with ONT HALNy HL-4Supported on Version: V2.0.9 or above
Revision1
Let us know how to improve below document on: support@halny.com

1. ONT Configuration (Access Mode – only INTERNET)

ONT is connected to the port 1/1/1 with onu ID 16

1. Create ONT interface and set up admin-state

#configure equipment ont interface 1/1/1/1/16 sernum HALN:206FAB23 sw-ver-pland disabled iphc-allowed enable-aes disabled
#configure equipment ont interface 1/1/1/1/16 admin-state up

2.Plan card slot type and define quantity and type of ports

#configure equipment ont slot 1/1/1/1/16/1 planned-card-type 10_100base plndnumdataports 4 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/16/1

3. Create QOS profile

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Assign DBA profiles to ethernet ports

admin>#configure qos interface 1/1/1/1/16/1/1 upstream-queue 0 bandwidth-profile name:1G

admin>#configure qos interface 1/1/1/1/16/1/2 upstream-queue 0 bandwidth-profile name:1G

admin>#configure qos interface 1/1/1/1/16/1/3 upstream-queue 0 bandwidth-profile name:1G

admin>#configure qos interface 1/1/1/1/16/1/4 upstream-queue 0 bandwidth-profile name:1G

5. Add vlan 100 to the bridge port eth1-4 as untagged vlan

admin>#configure bridge port 1/1/1/1/16/1/1
admin>configure>bridge>port>1/1/1/1/16/1/1$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/1>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/1# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/1# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/2
admin>configure>bridge>port>1/1/1/1/16/1/2$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/2>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/2# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/2# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/3
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/3# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/4
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/4# max-unicast-mac 200

6. ONT ip-host 1 configuration

#configure qos interface 1/1/1/1/16/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/16/vuni
#configure>bridge>port>1/1/1/1/16/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/16/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/16/1$ admin-state up

7. Enable ONT eth ports

#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/1# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/2# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/3# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up

8. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/16/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168
2. ONT Configuration (Access Mode – Internet, IPTV)

ONT is connected to the port 1/1/1 with onu ID 16

1. Create ONT interface and set up admin-state

#configure equipment ont interface 1/1/1/1/16 sernum HALN:206FAB23 sw-ver-pland disabled iphc-allowed enable-aes disabled
#configure equipment ont interface 1/1/1/1/16 admin-state up

2.Plan card slot type and define quantity and type of ports

#configure equipment ont slot 1/1/1/1/16/1 planned-card-type 10_100base plndnumdataports 4 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/16/1

3. Create QoS profile(ignore this step if You already created QoS profile)

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet ports speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/1 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/2 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/3 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/4 upstream-queue 0 bandwidth-profile name:1G

5. Add vlan 200 to eth1 bridge port as untagged and vlan 100 to eth2-4 bridge port as untagged vlan

admin>#configure bridge port 1/1/1/1/16/1/1
admin>configure>bridge>port>1/1/1/1/16/1/1$ vlan-id 200 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/1>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/1# pvid 200
admin>configure>bridge>port>1/1/1/1/16/1/1# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/2
admin>configure>bridge>port>1/1/1/1/16/1/2$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/2>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/2# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/2# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/3
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/3# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/4
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/4# max-unicast-mac 200

Remember to enable multicast control and forwarding on vlan 200

admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0

6. ONT ip-host 1 configuration

#configure qos interface 1/1/1/1/16/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/16/vuni
#configure>bridge>port>1/1/1/1/16/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/16/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/16/1$ admin-state up

7. Enable ONT eth ports

#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/1# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/2# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/3# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state u

8. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/16/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168
3. ONT Configuration (Transparent Mode – INTERNET, VOIP, IPTV)

ONT is connected to the port 1/1/1 with onu ID 16

1. Create ONT interface and set up admin-state

#configure equipment ont interface 1/1/1/1/16 sernum HALN:206FAB23 sw-ver-pland disabled iphc-allowed enable-aes disabled
#configure equipment ont interface 1/1/1/1/16 admin-state up

2.Plan card slot type and define quantity and type of ports

#configure equipment ont slot 1/1/1/1/16/1 planned-card-type 10_100base plndnumdataports 4 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/16/1

3. Create QoS profile(ignore this step if You already created QoS profile)

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet port speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/1 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/2 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/3 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/4 upstream-queue 0 bandwidth-profile name:1G

5. Add vlans 100,200, 300 to the bridge port eth1-4 as tagged vlans

admin>#configure bridge port 1/1/1/1/16/1/1
admin>configure>bridge>port>1/1/1/1/16/1/1$ vlan-id 100 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/1>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/1$ vlan-id 200 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/1>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/1$ vlan-id 300 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/1>vlan-id>300$ exit
admin>configure>bridge>port>1/1/1/1/16/1/1# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/2
admin>configure>bridge>port>1/1/1/1/16/1/2$ vlan-id 100 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/2>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/2$ vlan-id 200 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/2>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/2$ vlan-id 300 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/2>vlan-id>300$ exit
admin>configure>bridge>port>1/1/1/1/16/1/2# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/3
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 100 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 200 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 300 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>300$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/4
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 100 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 200 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 300 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>300$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4# max-unicast-mac 200

Remember to enable multicast control and forwarding on vlan 200

admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0

6. ONT ip-host 1 configuration

#configure qos interface 1/1/1/1/16/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/16/vuni
#configure>bridge>port>1/1/1/1/16/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/16/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/16/1$ admin-state up

7. Enable ONT eth ports

#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/1# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/2# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/3# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state u

8. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/16/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168
4. ONT configuration (Access + TRANSPARENT mode)

ONT is connected to the port 1/1/1 with onu ID 16

1. Create ONT interface and set up admin-state

#configure equipment ont interface 1/1/1/1/16 sernum HALN:206FAB23 sw-ver-pland disabled iphc-allowed enable-aes disabled
#configure equipment ont interface 1/1/1/1/16$ admin-state up

2.Plan card slot type and define quantity and type of ports

#configure equipment ont slot 1/1/1/1/16/1 planned-card-type 10_100base plndnumdataports 4 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/16/1

3. Create QoS profile(ignore this step if You already created QoS profile)

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet port speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/1 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/2 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/3 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/4 upstream-queue 0 bandwidth-profile name:1G

5. Add vlan 200 to bridge port eth1 as untagged vlan, 100 to bridge port eth2 as untagged vlan and 100,200, 300 to bridge port eth3-4 as tagged vlans:

admin>#configure bridge port 1/1/1/1/16/1/1
admin>configure>bridge>port>1/1/1/1/16/1/1$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/1>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/1# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/1# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/2
admin>configure>bridge>port>1/1/1/1/16/1/2$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/2>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/2# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/2# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/3
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 100 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 200 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 300 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>300$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/4
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 100 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 200 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 300 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>300$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4# max-unicast-mac 200

Remember to enable multicast control and forwarding on vlan 200

admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0

6. Enable ONT eth ports

#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/1# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/2# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/3# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state u

7. ONT ip-host 1 configuration

#configure qos interface 1/1/1/1/16/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/16/vuni
#configure>bridge>port>1/1/1/1/16/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/16/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/16/1$ admin-state up

8. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/16/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168
5. ONT Configuration (Vlan Translation – RBSA)


ONT is connected to the port 1/1/1 with onu ID 16

1. Create ONT interface and set up admin-state

#configure equipment ont interface 1/1/1/1/16 sernum HALN:206FAB23 sw-ver-pland disabled iphc-allowed enable-aes disabled
#configure equipment ont interface 1/1/1/1/16$ admin-state up

2.Plan card slot type and define quantity and type of ports

#configure equipment ont slot 1/1/1/1/16/1 planned-card-type 10_100base plndnumdataports 4 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/16/1

3. Create QoS profile(ignore this step if You already created QoS profile)

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet ports speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/1 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/2 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/3 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/4 upstream-queue 0 bandwidth-profile name:1G

5. Add vlans 100,200,300 to the bridge port eth1-4 and set vlan translation

typ:admin>configure>bridge>port>1/1/1/1/16/1/1
typ:admin>configure>bridge>port>1/1/1/1/16/1/1# vlan-id 35 l2fwder-vlan 100 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/1# vlan-id 838 l2fwder-vlan 200 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/1# vlan-id 839 l2fwder-vlan 300 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/1 max-unicast-mac 200

typ:admin>configure>bridge>port>1/1/1/1/16/1/2
typ:admin>configure>bridge>port>1/1/1/1/16/1/2# vlan-id 35 l2fwder-vlan 100 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/2# vlan-id 838 l2fwder-vlan 200 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/2# vlan-id 839 l2fwder-vlan 300 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/2 max-unicast-mac 200

typ:admin>configure>bridge>port>1/1/1/1/16/1/3
typ:admin>configure>bridge>port>1/1/1/1/16/1/3# vlan-id 35 l2fwder-vlan 100 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/3# vlan-id 838 l2fwder-vlan 200 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/3# vlan-id 839 l2fwder-vlan 300 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/3 max-unicast-mac 200

typ:admin>configure>bridge>port>1/1/1/1/16/1/3
typ:admin>configure>bridge>port>1/1/1/1/16/1/3# vlan-id 35 l2fwder-vlan 100 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/3# vlan-id 838 l2fwder-vlan 200 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/3# vlan-id 839 l2fwder-vlan 300 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/3 max-unicast-mac 200

Remember to enable multicast control and forwarding on vlan 200

admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0

6. ONT ip-host 1 configuration

#configure qos interface 1/1/1/1/16/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/16/vuni
#configure>bridge>port>1/1/1/1/16/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/16/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/16/1 admin-state up


7. Add user identification string to vlan 35 and vlan 838 – port eth 1-4 if necessary

configure interface port vlan-port:1/1/1/1/16/1/1:35 admin-up user "00C1777A22#1#01#01:16.01.01"
configure interface port vlan-port:1/1/1/1/16/1/1:838 admin-up user "03#1#01#01:016.01.01"

8. Add onu description

configure equipment ont interface 1/1/1/1/8 desc1 DESCRIPTION
configure equipment ont interface 1/1/1/1/8 desc2 DESCRIPTION2

9. Enable ONT eth ports

#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/1# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/2# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/3# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state u

10. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/16/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168

ONT HL-4G Provisioning on ISAM 7360

Provisioning is not supported in SFU mode.

ONT HL-4G upgrade on ISAM 7360

ONT upgrade process is described in this article.

Table of Contents
Hit enter to search or ESC to close

Search Page

The beauty of this theme is that is built with Modules. Every time you can active or dis-active any module that you would not need anymore ! Awesome WordPress Theme with latest technologies.

May We Suggest?