[NOKIA] OLT Integration with HALNy SFU 4 LAN

Created On10 June 2025

Last Updated On10 June 2025

byJakub Surowiec

HALNy Integration

Let us know how to improve below document on: support@halny.com

Service scenario

HALNy ONTs can work in two modes – HGU (Home Gateway Unit) and SFU (Single Family Unit).
HGU mode configuration is presented here.

Changing ONT mode is achieved by setting up/or not bridge port and VEIP for ONT. In example, if ONT has to be working as HGU, we need to set only VEIP. If as SFU, we need to set only bridge port(s).
SFU mode allows to prepare more complex configuration – such as QiQ tunnel or VLAN translation on the ONT.
In this tutorial, we will focus on SFU mode configuration.

ONT modes switching HGU<->SFU

Switching between HGU and SFU modes is described here.

ONT Configuration

1. ONT Configuration (Access Mode – only INTERNET)

Attention: Following configuration example is based on the HL-4G2 model, which features 4 LAN ports and 0 POTS ports. Adjust the configuration as needed to suit your ONT model.

ONT is connected to the port 1/1/1 with onu ID 16

1. Create ONT interface and set up admin-state

#configure equipment ont interface 1/1/1/1/16 sernum HALN:206FAB23 sw-ver-pland disabled iphc-allowed enable-aes disabled
#configure equipment ont interface 1/1/1/1/16 admin-state up

2.Plan card slot type and define quantity and type of ports

Remember to correctly specify the number of LAN and POTS ports on your ONT!

#configure equipment ont slot 1/1/1/1/16/1 planned-card-type 10_100base plndnumdataports 4 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/16/1

3. Create QOS profile

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Assign DBA profiles to ethernet ports

admin>#configure qos interface 1/1/1/1/16/1/1 upstream-queue 0 bandwidth-profile name:1G

admin>#configure qos interface 1/1/1/1/16/1/2 upstream-queue 0 bandwidth-profile name:1G

admin>#configure qos interface 1/1/1/1/16/1/3 upstream-queue 0 bandwidth-profile name:1G

admin>#configure qos interface 1/1/1/1/16/1/4 upstream-queue 0 bandwidth-profile name:1G

5. Add vlan 100 to the bridge port eth1-4 as untagged vlan

admin>#configure bridge port 1/1/1/1/16/1/1
admin>configure>bridge>port>1/1/1/1/16/1/1$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/1>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/1# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/1# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/2
admin>configure>bridge>port>1/1/1/1/16/1/2$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/2>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/2# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/2# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/3
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/3# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/4
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/4# max-unicast-mac 200

6. ONT ip-host 1 configuration

#configure qos interface 1/1/1/1/16/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/16/vuni
#configure>bridge>port>1/1/1/1/16/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/16/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/16/1$ admin-state up

7. Enable ONT eth ports

#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/1# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/2# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/3# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up

8. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/16/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168

2. ONT Configuration (Access Mode – Internet, IPTV)

Attention: Following configuration example is based on the HL-4G2 model, which features 4 LAN ports and 0 POTS ports. Adjust the configuration as needed to suit your ONT model.

ONT is connected to the port 1/1/1 with onu ID 16

1. Create ONT interface and set up admin-state

#configure equipment ont interface 1/1/1/1/16 sernum HALN:206FAB23 sw-ver-pland disabled iphc-allowed enable-aes disabled
#configure equipment ont interface 1/1/1/1/16 admin-state up

2.Plan card slot type and define quantity and type of ports

Remember to correctly specify the number of LAN and POTS ports on your ONT!

#configure equipment ont slot 1/1/1/1/16/1 planned-card-type 10_100base plndnumdataports 4 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/16/1

3. Create QoS profile

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet ports speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/1 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/2 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/3 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/4 upstream-queue 0 bandwidth-profile name:1G

5. Add vlan 200 to eth1 bridge port as untagged and vlan 100 to eth2-4 bridge port as untagged vlan

admin>#configure bridge port 1/1/1/1/16/1/1
admin>configure>bridge>port>1/1/1/1/16/1/1$ vlan-id 200 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/1>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/1# pvid 200
admin>configure>bridge>port>1/1/1/1/16/1/1# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/2
admin>configure>bridge>port>1/1/1/1/16/1/2$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/2>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/2# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/2# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/3
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/3# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/4
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/4# max-unicast-mac 200

Remember to enable multicast control and forwarding on vlan 200

admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0

6. ONT ip-host 1 configuration

#configure qos interface 1/1/1/1/16/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/16/vuni
#configure>bridge>port>1/1/1/1/16/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/16/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/16/1$ admin-state up

7. Enable ONT eth ports

#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/1# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/2# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/3# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up

8. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/16/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168

3. ONT Configuration (Transparent Mode – INTERNET, VOIP, IPTV)

Attention: Following configuration example is based on the HL-4G2 model, which features 4 LAN ports and 0 POTS ports. Adjust the configuration as needed to suit your ONT model.

ONT is connected to the port 1/1/1 with onu ID 16

1. Create ONT interface and set up admin-state

#configure equipment ont interface 1/1/1/1/16 sernum HALN:206FAB23 sw-ver-pland disabled iphc-allowed enable-aes disabled
#configure equipment ont interface 1/1/1/1/16 admin-state up

2.Plan card slot type and define quantity and type of ports

Remember to correctly specify the number of LAN and POTS ports on your ONT!

#configure equipment ont slot 1/1/1/1/16/1 planned-card-type 10_100base plndnumdataports 4 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/16/1

3. Create QoS profile(ignore this step if You already created QoS profile)

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet port speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/1 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/2 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/3 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/4 upstream-queue 0 bandwidth-profile name:1G

5. Add vlans 100,200, 300 to the bridge port eth1-4 as tagged vlans

admin>#configure bridge port 1/1/1/1/16/1/1
admin>configure>bridge>port>1/1/1/1/16/1/1$ vlan-id 100 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/1>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/1$ vlan-id 200 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/1>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/1$ vlan-id 300 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/1>vlan-id>300$ exit
admin>configure>bridge>port>1/1/1/1/16/1/1# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/2
admin>configure>bridge>port>1/1/1/1/16/1/2$ vlan-id 100 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/2>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/2$ vlan-id 200 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/2>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/2$ vlan-id 300 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/2>vlan-id>300$ exit
admin>configure>bridge>port>1/1/1/1/16/1/2# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/3
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 100 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 200 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 300 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>300$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/4
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 100 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 200 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 300 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>300$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4# max-unicast-mac 200

Remember to enable multicast control and forwarding on vlan 200

admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0

6. ONT ip-host 1 configuration

#configure qos interface 1/1/1/1/16/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/16/vuni
#configure>bridge>port>1/1/1/1/16/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/16/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/16/1$ admin-state up

7. Enable ONT eth ports

#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/1# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/2# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/3# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up

8. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/16/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168

4. ONT configuration (Access + TRANSPARENT mode)

Attention: Following configuration example is based on the HL-4G2 model, which features 4 LAN ports and 0 POTS ports. Adjust the configuration as needed to suit your ONT model.

ONT is connected to the port 1/1/1 with onu ID 16

1. Create ONT interface and set up admin-state

#configure equipment ont interface 1/1/1/1/16 sernum HALN:206FAB23 sw-ver-pland disabled iphc-allowed enable-aes disabled
#configure equipment ont interface 1/1/1/1/16$ admin-state up

2.Plan card slot type and define quantity and type of ports

Remember to correctly specify the number of LAN and POTS ports on your ONT!

#configure equipment ont slot 1/1/1/1/16/1 planned-card-type 10_100base plndnumdataports 4 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/16/1

3. Create QoS profile(ignore this step if You already created QoS profile)

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet port speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/1 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/2 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/3 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/4 upstream-queue 0 bandwidth-profile name:1G

5. Add vlan 200 to bridge port eth1 as untagged vlan, 100 to bridge port eth2 as untagged vlan and 100,200, 300 to bridge port eth3-4 as tagged vlans:

admin>#configure bridge port 1/1/1/1/16/1/1
admin>configure>bridge>port>1/1/1/1/16/1/1$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/1>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/1# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/1# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/2
admin>configure>bridge>port>1/1/1/1/16/1/2$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/16/1/2>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/2# pvid 100
admin>configure>bridge>port>1/1/1/1/16/1/2# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/3
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 100 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 200 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3$ vlan-id 300 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/3>vlan-id>300$ exit
admin>configure>bridge>port>1/1/1/1/16/1/3# max-unicast-mac 200

admin>#configure bridge port 1/1/1/1/16/1/4
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 100 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 200 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4$ vlan-id 300 tag single-taged
admin>configure>bridge>port>1/1/1/1/16/1/4>vlan-id>300$ exit
admin>configure>bridge>port>1/1/1/1/16/1/4# max-unicast-mac 200

Remember to enable multicast control and forwarding on vlan 200

admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0

6. Enable ONT eth ports

#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/1# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/2# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/3# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up

7. ONT ip-host 1 configuration

#configure qos interface 1/1/1/1/16/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/16/vuni
#configure>bridge>port>1/1/1/1/16/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/16/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/16/1$ admin-state up

8. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/16/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168

5. ONT Configuration (Vlan Translation – RBSA)

Attention: Following configuration example is based on the HL-4G2 model, which features 4 LAN ports and 0 POTS ports. Adjust the configuration as needed to suit your ONT model.

ONT is connected to the port 1/1/1 with onu ID 16

1. Create ONT interface and set up admin-state

#configure equipment ont interface 1/1/1/1/16 sernum HALN:206FAB23 sw-ver-pland disabled iphc-allowed enable-aes disabled
#configure equipment ont interface 1/1/1/1/16$ admin-state up

2.Plan card slot type and define quantity and type of ports

Remember to correctly specify the number of LAN and POTS ports on your ONT!

#configure equipment ont slot 1/1/1/1/16/1 planned-card-type 10_100base plndnumdataports 4 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/16/1

3. Create QoS profile(ignore this step if You already created QoS profile)

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet ports speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/1 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/2 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/3 upstream-queue 0 bandwidth-profile name:1G

admin>#configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/16/1/4 upstream-queue 0 bandwidth-profile name:1G

5. Add vlans 100,200,300 to the bridge port eth1-4 and set vlan translation

typ:admin>configure>bridge>port>1/1/1/1/16/1/1
typ:admin>configure>bridge>port>1/1/1/1/16/1/1# vlan-id 35 l2fwder-vlan 100 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/1# vlan-id 838 l2fwder-vlan 200 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/1# vlan-id 839 l2fwder-vlan 300 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/1 max-unicast-mac 200

typ:admin>configure>bridge>port>1/1/1/1/16/1/2
typ:admin>configure>bridge>port>1/1/1/1/16/1/2# vlan-id 35 l2fwder-vlan 100 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/2# vlan-id 838 l2fwder-vlan 200 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/2# vlan-id 839 l2fwder-vlan 300 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/2 max-unicast-mac 200

typ:admin>configure>bridge>port>1/1/1/1/16/1/3
typ:admin>configure>bridge>port>1/1/1/1/16/1/3# vlan-id 35 l2fwder-vlan 100 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/3# vlan-id 838 l2fwder-vlan 200 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/3# vlan-id 839 l2fwder-vlan 300 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/3 max-unicast-mac 200

typ:admin>configure>bridge>port>1/1/1/1/16/1/3
typ:admin>configure>bridge>port>1/1/1/1/16/1/3# vlan-id 35 l2fwder-vlan 100 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/3# vlan-id 838 l2fwder-vlan 200 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/3# vlan-id 839 l2fwder-vlan 300 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/16/1/3 max-unicast-mac 200

Remember to enable multicast control and forwarding on vlan 200

admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0

6. ONT ip-host 1 configuration

#configure qos interface 1/1/1/1/16/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/16/vuni
#configure>bridge>port>1/1/1/1/16/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/16/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/16/1 admin-state up

7. Add user identification string to vlan 35 and vlan 838 – port eth 1-4 if necessary

configure interface port vlan-port:1/1/1/1/16/1/1:35 admin-up user "00C1777A22#1#01#01:16.01.01"
configure interface port vlan-port:1/1/1/1/16/1/1:838 admin-up user "03#1#01#01:016.01.01"

8. Add onu description

configure equipment ont interface 1/1/1/1/8 desc1 DESCRIPTION
configure equipment ont interface 1/1/1/1/8 desc2 DESCRIPTION2

9. Enable ONT eth ports

#configure ethernet ont 1/1/1/1/16/1/1 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/1# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/2 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/2# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/3 auto-detect auto admin-state up
typ:isadmin>configure>ethernet>ont>1/1/1/1/16/1/3# exit all
typ:isadmin># configure ethernet ont 1/1/1/1/16/1/4 auto-detect auto admin-state up

10. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/16/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168

HALNy ONT Provisioning on ISAM 7360

There are two ways of ONT provisioning:

TR-069(link)

DHCP option 66,67 (link)

HALNy ONT upgrade on ISAM 7360

ONT upgrade process is described in this article.


Model	WAN ports	LAN ports	WiFi	WiFi speed	Antennas	VoIP	Sales Status
Ethernet Routers
HLE-3GX-F	1×10/100/1000	3×10/100/1000	2T2R WiFi6	1800AX	Internal	-	In daily sales
HLE-4BX3V-F	1×100/1000/2500 Ethernet	3×10/100/1000 + 1×2500	2T2R WiFi6	WiFi6 AX3000	Internal	1xFXS	Coming soon!
Active Ethernet (SFP WAN)
HLS-4BX3V-F	1×1000/2500 SFP port	3×10/100/1000 + 1×2500	2T2R WiFi6	WiFi6 AX3000	Internal	1xFXS	Coming soon!
Fiber Tray for ONT based on CUBE housing
HL-FIBER-TRAY	-	-	-	-	-	-	In daily sales


Model Name	Mode	LAN	VoIP	WiFi	Mode button	Sales Status
HLX-SFPX	SFU (Bridge only)	1x1000/10000	-	-	-	New one! In daily sales
HLX-1TL	SFU (Bridge only)	1x1000/2500/10000	-	-	-	Coming soon! Q1-25
HLX-1TLV	SFU (Bridge only)	1x1000/2500/10000	1	-	-	New one! In daily sales
HLX-TGV	SFU (bridge) HGU (router NAT)	1x1000/2500/10000 1x10/100/1000	2	-	-	In daily sales
HLX-4BYV-F	HGU (router NAT)	1x100/1000/2500 3x10/100/1000	1	WIFI 7 Triband 2.4/5/6GHz	Yes	Coming soon!
Fiber Tray for ONT based on CUBE housing
HL-FIBER-TRAY	-	-	-	-	-	In daily sales


Model	LAN ports	VoIP FXS POTS port	WiFi	WiFi antennas grain and type	WiFi speed	RF/CATV overlay	EtherWAN (LAN4 as Wan port)	USB port	SALES STATUS
HL-GSFP	SFP 1GbE/2.5GbE	-	-	-	-	-	-	-	In daily sales
HL-1GE	1×10/100/1000	-	-	-	-	-	-	-	In daily sales
HL-1GC	1×10/100/1000	-	-	-	-	-	-	-	In daily sales
HL-1B	1×100/1000/2500	-	-	-	-	-	-	-	New one! In daily sales
HL-4G2	4×10/100/1000	-	-	-	-	-	-	-	New one! In daily sales
HL-1GR	1×10/100/1000	-	-	-	-	1	-	-	In daily sales
HL-2BV	1×1000/2500 1×10/100/1000	1	-	-	-	-	-	-	In daily sales
HL-4GV	4×10/100/1000	2	-	-	-	-	-	-	New one! In daily sales
HL-4GMV2	4×10/100/1000	2	2T2R 802.11n 2T2R 802.11ac wave2	2x5dB (external)	866Mbps 5Ghz 300Mbps 2.4Ghz	-	YES	-	In daily sales
HL-4GMVR	4×10/100/1000	1	2T2R 802.11n 2T2R 802.11ac wave2	4x5dB (external)	866Mbps 5Ghz 300Mbps 2.4Ghz	1	YES	-	In daily sales
HL-4GX3VR	4×10/100/1000	1	2T2R AX3000 WiFi6	4x5dB (external)	3000Mbps for 2.4Ghz / 5Ghz	1	YES	-	New one! In daily sales
HL-4GXV-F	4×10/100/1000	1	802.11ax 1800AX WiFi6	2x2 internal	1800Mbs for 2.4Ghz / 5Ghz	-	YES	-	In daily sales
HL-4GXVU-F	4×10/100/1000	1	802.11ax 1800AX WiFi6	2x2 internal	1800Mbs for 2.4Ghz / 5Ghz	-	YES	1	New one! In daily sales
HL-4BX3V-F	3×10/100/1000 1×2500	1	2T3R AX3000 WiFi6	2x3 Internal	3000Mbs for 2.4Ghz / 5Ghz	-	YES	-	New one! In daily sales
HL-4BY3V-F	1x100/1000/2500 3x10/100/1000	1	WIFI 7 Dual-Band 2.4Ghz/5Ghz	Internal	BE3600	-	YES	-	Coming soon!
HL-4BY7V-F	1x100/1000/2500 3x10/100/1000	1	WIFI 7 Dual-Band 2.4Ghz/5Ghz 4x4	Internal	BE7200	-	YES	-	Coming soon!
Fiber Tray for ONT based on CUBE housing
HL-FIBER-TRAY	-	-	-	-	-	-	-	-	In daily sales

Have a Question?

[NOKIA] OLT Integration with HALNy SFU 4 LAN

Service scenario

ONT modes switching HGU<->SFU

ONT Configuration

1. ONT Configuration (Access Mode – only INTERNET)

2. ONT Configuration (Access Mode – Internet, IPTV)

3. ONT Configuration (Transparent Mode – INTERNET, VOIP, IPTV)

4. ONT configuration (Access + TRANSPARENT mode)

5. ONT Configuration (Vlan Translation – RBSA)

HALNy ONT Provisioning on ISAM 7360

HALNy ONT upgrade on ISAM 7360