HL-2BV HGU Configuration [ZTE C6XX]

HALNy HL-2BV Configuration

Service scenario

HL-2BV can work in two modes – HGU (Home Gateway Unit) and SFU (Single Family Unit).
SFU mode configuration is presented here.
Managing ONT mode is done by setting up/or not bridge port and VEIP for ONT. In example, if ONT has to be working as HGU, we need to set only VEIP. If as SFU, we need to set bridge port(s) and VEIP(only if we want to use ip-host).
SFU mode allows to prepare more complex configuration – such as QinQ tunnel or VLAN translation on the ONT. In this tutorial we will focus on HGU mode configuration.

ONT modes switching HGU<->SFU

Switching between HGU and SFU modes is described here.

ONT configuration

This tutorial is based on ONT with firmware V4.0.8p1 and ZTE C610 running with firmware V1.2.2.

In example configuration we used below VLANs:
VLAN 10 – INTERNET
VLAN 20 – VoIP
VLAN 40 – IPTV (multicast uplink port 1/1/6)
VLAN 400 – MGMT 

1. Create DBA profile

(config)# gpon
  profile tcont MAX type 4 maximum 102400

2. Create ONT Type
Change HL-MODEL string to exact model name of the ONT, ex. onu-type HL-4GMV gpon …

(config)# pon
  onu-type HL-2BV gpon max-tcont 4 max-gemport 32 max-iphost 4
  onu-type-if HL-2BV eth_0/1
  onu-type-if HL-2BV eth_0/2
  onu-type-if HL-2BV pots_0/1

3. Register ONT on GPON

(config)# interface gpon-olt_1/3/3 
  onu 8 type HL-2BV sn HALN5A6FA578

4. Configure ONT interface mode

(config)# interface gpon-onu_1/3/3:8 
  real-speed gpon
  vport-mode manual
  tcont 1 profile MAX
  tcont 2 profile MAX
  tcont 3 profile MAX
  tcont 4 profile MAX
  gemport 1 tcont 1
  gemport 2 tcont 2
  gemport 3 tcont 3
  gemport 4 tcont 4
  vport 1 map-type vlan
  vport 2 map-type vlan
  vport 3 map-type vlan
  vport 4 map-type vlan
  vport-map 1 1 vlan 10
  vport-map 2 2 vlan 20
  vport-map 3 3 vlan 40
  vport-map 4 4 vlan 400

5. Create igmp profile

onu profile igmp 20 down-tag strip

6. Create vlan-profile (for IP host 1)

onu profile vlan tag400 tag-mode tag cvlan 400

7. Configure ONT remote management mode

(config)# pon-onu-mng gpon-onu_1/3/3:8
  mvlan 20
  service 1 gemport 1 vlan 10
  service 2 gemport 2 vlan 20
  service 3 gemport 3 vlan 40
  service 4 gemport 4 vlan 400
  igmp eth_0/1 profile 20
  wan-ip ipv4 mode dhcp vlan-profile tag400 host 1
  vlan port eth_0/1 mode hybrid def-vlan 20
  vlan port eth_0/2 mode hybrid def-vlan 10

8. Configure vports.

interface vport-1/3/3.8:1
  service-port 1 user-vlan 10 vlan 10
$
interface vport-1/3/3.8:2
  service-port 2 user-vlan 20 vlan 20
  igmp fast-leave enable
  igmp version v2
$
interface vport-1/3/3.8:3
  service-port 3 user-vlan 40 vlan 40
$
interface vport-1/3/3.8:3
  service-port 4 user-vlan 400 vlan 400

9. Configure IGMP Snooping

(config)# igmp querygemport-mode both
(config)# igmp  mvlan 20
(config-igmp-mvlan-20)# source-port xxvgei-1/1/6
(config-igmp-mvlan-20)# receive-port vport-1/3/3.8:2
(config-igmp-mvlan-20)# host-version v2
(config-igmp-mvlan-20)# work-mode snooping

10. Verify ONT ip-host 1 IP address

#show gpon remote-onu ip-host gpon-onu_1/3/3:8
Host ID:            1
Host name:          IPHOST: WWW/XML/TR069
Identify:
IP addres:          0.0.0.0
Mask:               0.0.0.0
Gateway:            0.0.0.0
Primary DNS:        0.0.0.0
Second DNS:         0.0.0.0
DHCP enable:        disable
Ping response:      disable
Traceroute response:disable
MAC address:        54DB.5A6F.A578
Current IP address: 172.17.60.136
Current mask:       255.255.254.0
Current gateway:    172.17.60.1
Current primary DNS:172.17.61.224
Current second DNS: 172.17.60.1
Domain name:

ONT HL-2BV Provisioning on ZTE C610

There are two ways of ONT provisioning:

• DHCP option 66,67 (link)
• TR-069(link)

ONT HL-2BV Upgrade on ZTE C610

Upgrade procedure is the same as for other HALNy ONTs (link)