HALNy HLX-SFPX SFU Configuration [NOKIA 7360]

Created On30 April 2025

Last Updated On7 May 2025

byPiotr Dydo

HALNy HLX-SFPX Configuration

Service scenario

HLX-SFPX works only in SFU (bridge) mode. SFU mode allows to prepare different configurations – such as QinQ tunnel or VLAN translation on the ONT.

Supported SFU service scenario and ONT configuration

Document Date and version	2025.04.29
Tested on OLT NOKIA 7360 FX-4	Version: L6GPAA56.587
Tested with ONT HALNy HLX-SFPX	Supported on Version: V7.0.5p2 or above
Revision	1

Let us know how to improve below document on: support@halny.com

Credentials for web management

LAN IP address: 192.168.33.1
User: useradmin
Password: useradmin123

1. ONT Configuration (Access Mode – only INTERNET)

ONT is connected to the port 1/1/1 with onu ID 8
1. Create ONT interface and set up admin-state

admin>#configure equipment ont interface 1/1/1/1/8 sernum HALN:945F1AC8 sw-ver-pland disabled iphc-allowed enable enable-aes disable planned-us-rate 10g
configure>equipment>ont>interface>1/1/1/1/8 admin-state up

2. Plan card slot type and definie quantity and type of ports (1 ETH in case of HLX-SFPX)

admin>#configure equipment ont slot 1/1/1/1/8/1 planned-card-type ethernet plndnumdataports 1 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/8/1

3. Create QoS profile

#configure qos profiles bandwidth 10G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 10000000

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet port speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/8/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/8/1/1 upstream-queue 0 bandwidth-profile name:10G

5. Add vlan 100 to the bridge port

admin>#configure bridge port 1/1/1/1/8/1/1
admin>configure>bridge>port>1/1/1/1/8/1/1$ vlan-id 100 tag untagged
admin>configure>bridge>port>1/1/1/1/8/1/1>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/8/1/1# pvid 100
admin>configure>bridge>port>1/1/1/1/8/1/1# max-unicast-mac 200

6. Optionally configure ip-host 1

#configure qos interface 1/1/1/1/8/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/8/vuni
#configure>bridge>port>1/1/1/1/8/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/8/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/8/1$ admin-state up

7. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/8/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168

NOTE: In order to ip-host work properly, the broadcast should be enabled on VLAN

#configure vlan id 400 new-broadcast enable

2. ONT Configuration (Access Mode – only IPTV)

ONT is connected to the port 1/1/1 with onu ID 8
1. Create ONT interface and set up admin-state

admin>#configure equipment ont interface 1/1/1/1/8 sernum HALN:945F1AC8 sw-ver-pland disabled iphc-allowed enable enable-aes disable planned-us-rate 10g
configure>equipment>ont>interface>1/1/1/1/8 admin-state up

2. Plan card slot type and definie quantity and type of ports (1 ETH in case of HLX-SFPX)

admin>#configure equipment ont slot 1/1/1/1/8/1 planned-card-type ethernet plndnumdataports 1 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/8/1

3. Create QoS profile

#configure qos profiles bandwidth 10G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 10000000

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet port speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/8/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/8/1/1 upstream-queue 0 bandwidth-profile name:10G

5. Add vlan 200 to the bridge port

admin>#configure bridge port 1/1/1/1/8/1/1
admin>configure>bridge>port>1/1/1/1/8/1/1$ vlan-id 200 tag untagged
admin>configure>bridge>port>1/1/1/1/8/1/1>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/8/1/1# pvid 200
admin>configure>bridge>port>1/1/1/1/8/1/1# max-unicast-mac 200

Remember to enable multicast control and forwarding on vlan 200

admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0

6. Optionally configure ip-host 1

#configure qos interface 1/1/1/1/8/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/8/vuni
#configure>bridge>port>1/1/1/1/8/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/8/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/8/1$ admin-state up

7. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/8/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168

NOTE: In order to ip-host work properly, the broadcast should be enabled on VLAN

#configure vlan id 400 new-broadcast enable

3. ONT Configuration (Transparent Mode – INTERNET, VOIP, IPTV)

ONT is connected to the port 1/1/1 with onu ID 8
1. Create ONT interface and set up admin-state

admin>#configure equipment ont interface 1/1/1/1/8 sernum HALN:945F1AC8 sw-ver-pland disabled iphc-allowed enable enable-aes disable planned-us-rate 10g
configure>equipment>ont>interface>1/1/1/1/8 admin-state up

2. Plan card slot type and definie quantity and type of ports (1 ETH in case of HLX-SFPX)

admin>#configure equipment ont slot 1/1/1/1/8/1 planned-card-type ethernet plndnumdataports 1 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/8/1

3. Create QoS profile

#configure qos profiles bandwidth 10G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 10000000

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet port speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/8/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/8/1/1 upstream-queue 0 bandwidth-profile name:10G

5. Add vlans 100, 200,300 as tagged to the bridge port

admin>#configure bridge port 1/1/1/1/8/1/1
admin>configure>bridge>port>1/1/1/1/8/1/1$ vlan-id 100 tag single-tagged
admin>configure>bridge>port>1/1/1/1/8/1/1>vlan-id>100$ exit
admin>configure>bridge>port>1/1/1/1/8/1/1$ vlan-id 200 tag single-tagged
admin>configure>bridge>port>1/1/1/1/8/1/1>vlan-id>200$ exit
admin>configure>bridge>port>1/1/1/1/8/1/1$ vlan-id 300 tag single-tagged
admin>configure>bridge>port>1/1/1/1/8/1/1>vlan-id>300$ exit
admin>configure>bridge>port>1/1/1/1/8/1/1# max-unicast-mac 200

Remember to enable multicast control and forwarding on vlan 200

admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0

6. Optionally configure ip-host 1

#configure qos interface 1/1/1/1/8/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/8/vuni
#configure>bridge>port>1/1/1/1/8/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/8/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/8/1$ admin-state up

7. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/8/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168

NOTE: In order to ip-host work properly, the broadcast should be enabled on VLAN

#configure vlan id 400 new-broadcast enable

4. ONT Configuration (Vlan Translation – RBSA)

ONT is connected to the port 1/1/1 with onu ID 8
1. Create ONT interface and set up admin-state

admin>#configure equipment ont interface 1/1/1/1/8 sernum HALN:945F1AC8 sw-ver-pland disabled iphc-allowed enable enable-aes disable planned-us-rate 10g
configure>equipment>ont>interface>1/1/1/1/8 admin-state up

2. Plan card slot type and definie quantity and type of ports (1 ETH in case of HLX-SFPX)

admin>#configure equipment ont slot 1/1/1/1/8/1 planned-card-type ethernet plndnumdataports 1 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/8/1

3. Create QoS profile

#configure qos profiles bandwidth 10G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 10000000

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet port speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/8/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/8/1/1 upstream-queue 0 bandwidth-profile name:10G

5. Add vlans 100, 200,300 as tagged to the bridge port and set vlan translation

admin>#configure bridge port 1/1/1/1/8/1/1
typ:admin>configure>bridge>port>1/1/1/1/8/1/1# vlan-id 35 l2fwder-vlan 100 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/8/1/1# vlan-id 838 l2fwder-vlan 200 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/8/1/1# vlan-id 839 l2fwder-vlan 300 vlan-scope local
typ:admin>configure>bridge>port>1/1/1/1/8/1/1 max-unicast-mac 200

Remember to enable multicast control and forwarding on vlan 200

admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0

6. Add user identification string to vlan 35 and vlan 838

configure interface port vlan-port:1/1/1/1/8/1/1:35 admin-up user "00C1777A22#1#01#01:08.01.01"
configure interface port vlan-port:1/1/1/1/8/1/1:838 admin-up user "03#1#01#01:08.01.01"

7.Add onu description

configure equipment ont interface 1/1/1/1/8 desc1 DESCRIPTION
configure equipment ont interface 1/1/1/1/8 desc2 DESCRIPTION2

8. Optionally configure ip-host 1

#configure qos interface 1/1/1/1/8/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/8/vuni
#configure>bridge>port>1/1/1/1/8/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/8/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/8/1$ admin-state up

9. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/8/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168

NOTE: In order to ip-host work properly, the broadcast should be enabled on VLAN

#configure vlan id 400 new-broadcast enable

5. ONT Configuration (QinQ – INTERNET, VOIP, IPTV – unrestricted c-VLANs)

Before ONT configuration, set VLAN stacking on OLT (with NOT specified C-VLANs)

configure vlan id stacked:999:0 mode residential-bridge in-qos-prof-name name:Default_TC0

ONT is connected to the port 1/1/1 with onu ID 8
1. Create ONT interface and set up admin-state

admin>#configure equipment ont interface 1/1/1/1/8 sernum HALN:945F1AC8 sw-ver-pland disabled iphc-allowed enable enable-aes disable planned-us-rate 10g
configure>equipment>ont>interface>1/1/1/1/8 admin-state up

2. Plan card slot type and definie quantity and type of ports (1 ETH in case of HLX-SFPX)

admin>#configure equipment ont slot 1/1/1/1/8/1 planned-card-type ethernet plndnumdataports 1 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/8/1

3. Create QoS profile

#configure qos profiles bandwidth 10G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 10000000

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet port speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/8/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/8/1/1 upstream-queue 0 bandwidth-profile name:10G

5. Add S-VLAN as stacked VLAN 999

admin>#configure bridge port 1/1/1/1/8/1/1
typ:admin>configure>bridge>port>1/1/1/1/8/1/1 max-unicast-mac 200
 vlan-id stacked:999:0
 tag single-tagged
exit

pvid stacked:999:0

Remember to enable multicast control and forwarding on vlan 200

admin>#configure id 200 mode residential-bridge ipv4-mcast-ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0

6. Optionally configure ip-host 1

#configure qos interface 1/1/1/1/8/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/8/vuni
#configure>bridge>port>1/1/1/1/8/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/8/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/8/1$ admin-state up

7. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/8/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168

NOTE: In order to ip-host work properly, the broadcast should be enabled on VLAN

#configure vlan id 400 new-broadcast enable

6. ONT Configuration (QinQ – INTERNET, VOIP, IPTV – restricted c-VLANs)

Before ONT configuration, set VLAN stacking on OLT (with specified C-VLANs)

configure vlan id stacked:999:100 mode residential-bridge in-qos-prof-name name:Default_TC0 
configure vlan id stacked:999:200 mode residential-bridge in-qos-prof-name name:Default_TC0 
configure vlan id stacked:999:300 mode residential-bridge in-qos-prof-name name:Default_TC0

ONT is connected to the port 1/1/1 with onu ID 8
1. Create ONT interface and set up admin-state

admin>#configure equipment ont interface 1/1/1/1/8 sernum HALN:945F1AC8 sw-ver-pland disabled iphc-allowed enable enable-aes disable planned-us-rate 10g
configure>equipment>ont>interface>1/1/1/1/8$ admin-state up

2. Plan card slot type and definie quantity and type of ports (1 ETH in case of HLX-SFPX)

admin>#configure equipment ont slot 1/1/1/1/8/1 planned-card-type ethernet plndnumdataports 1 plndnumvoiceports 0 admin-state up

NOTE:
Slot 1 is for Ethernet card -> #configure equipment ont slot 1/1/1/1/8/1

3. Create QoS profile

#configure qos profiles bandwidth 10G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 10000000

#configure qos profiles bandwidth 1G committed-info-rate 0 assured-info-rate 0 excessive-info-rate 1000000

4. Set ethernet port speed/duplex and assign DBA profile

admin>#configure ethernet ont 1/1/1/1/8/1/1 auto-detect auto admin-state up
admin>#configure qos interface 1/1/1/1/8/1/1 upstream-queue 0 bandwidth-profile name:10G

5. Add S-VLAN as stacked VLAN 999

admin>#configure bridge port 1/1/1/1/8/1/1
typ:admin>configure>bridge>port>1/1/1/1/8/1/1
  max-unicast-mac 200
  vlan-id 100
    tag single-tagged
    l2fwder-vlan stacked:999:100
    vlan-scope local
 exit
  vlan-id 200
    tag single-tagged
    l2fwder-vlan stacked:999:200
    vlan-scope local
 exit
  vlan-id 300
    tag single-tagged
    l2fwder-vlan stacked:999:300
    vlan-scope local
  exit

Remember to enable multicast control and forwarding on vlan 200

admin>#configure id stacked:999:200 mode residential-bridge ipv4-mcast-ctrl mac-mcast-ctrl in-qos-prof-name name:Default_TC0

6. Optionally configure ip-host 1

#configure qos interface 1/1/1/1/8/vuni upstream-queue 0 bandwidth-profile name:1G
#configure bridge port 1/1/1/1/8/vuni
#configure>bridge>port>1/1/1/1/8/vuni$ vlan-id 400 
#configure iphost ont ont:1/1/1/1/8/1 dhcp enabled vlan 400
#typ:isadmin>configure>iphost>ont>ont:1/1/1/1/8/1$ admin-state up

7. Display ONT ip-host 1 address

#show iphost ont operational-data
operational-data table
=========================================================================================================
index                    |ip-address     |net-mask       |default-router |dns-addr      |sec-dns-addr
-------------------------+---------------+---------------+---------------+--------------+---------------
ont:1/1/1/1/8/1           172.17.180.90    255.255.255.0   172.17.180.1   172.16.180.240  185.228.168.168

NOTE: In order to ip-host work properly, the broadcast should be enabled on VLAN

#configure vlan id 400 new-broadcast enable

ONT HLX-SFPX upgrade on ISAM 7360

ONT upgrade process is described in this article.


Model	WAN ports	LAN ports	WiFi	WiFi speed	Antennas	VoIP	Sales Status
Ethernet Routers
HLE-3GX-F	1×10/100/1000	3×10/100/1000	2T2R WiFi6	1800AX	Internal	-	In daily sales
HLE-4BX3V-F	1×100/1000/2500 Ethernet	3×10/100/1000 + 1×2500	2T2R WiFi6	WiFi6 AX3000	Internal	1xFXS	Coming soon!
Active Ethernet (SFP WAN)
HLS-4BX3V-F	1×1000/2500 SFP port	3×10/100/1000 + 1×2500	2T2R WiFi6	WiFi6 AX3000	Internal	1xFXS	Coming soon!
Fiber Tray for ONT based on CUBE housing
HL-FIBER-TRAY	-	-	-	-	-	-	In daily sales


Model Name	Mode	LAN	VoIP	WiFi	Mode button	Sales Status
HLX-SFPX	SFU (Bridge only)	1x1000/10000	-	-	-	Coming soon! Q1-25
HLX-1TL	SFU (Bridge only)	1x1000/2500/10000	-	-	-	Coming soon! Q1-25
HLX-1TLV	SFU (Bridge only)	1x1000/2500/10000	1	-	-	Coming soon! Q1-25
HLX-TGV	SFU (bridge) HGU (router NAT)	1x1000/2500/10000 1x10/100/1000	2	-	-	In daily sales
HLX-4BYV-F	HGU (router NAT)	1x100/1000/2500 3x10/100/1000	1	WIFI 7 Triband 2.4/5/6GHz	Yes	Coming soon!
Fiber Tray for ONT based on CUBE housing
HL-FIBER-TRAY	-	-	-	-	-	In daily sales


Model	LAN ports	VoIP FXS POTS port	WiFi	WiFi antennas grain and type	WiFi speed	RF/CATV overlay	EtherWAN (LAN4 as Wan port)	USB port	SALES STATUS
HL-GSFP	SFP 1GbE/2.5GbE	-	-	-	-	-	-	-	In daily sales
HL-1GE	1×10/100/1000	-	-	-	-	-	-	-	In daily sales
HL-1GC	1×10/100/1000	-	-	-	-	-	-	-	In daily sales
HL-1B	1×100/1000/2500	-	-	-	-	-	-	-	New one! In daily sales
HL-4G2	4×10/100/1000	-	-	-	-	-	-	-	New one! In daily sales
HL-1GR	1×10/100/1000	-	-	-	-	1	-	-	In daily sales
HL-2BV	1×1000/2500 1×10/100/1000	1	-	-	-	-	-	-	In daily sales
HL-4GV	4×10/100/1000	2	-	-	-	-	-	-	New one! In daily sales
HL-4GMV2	4×10/100/1000	2	2T2R 802.11n 2T2R 802.11ac wave2	2x5dB (external)	866Mbps 5Ghz 300Mbps 2.4Ghz	-	YES	-	In daily sales
HL-4GMVR	4×10/100/1000	1	2T2R 802.11n 2T2R 802.11ac wave2	4x5dB (external)	866Mbps 5Ghz 300Mbps 2.4Ghz	1	YES	-	In daily sales
HL-4GX3VR	4×10/100/1000	1	2T2R AX3000 WiFi6	4x5dB (external)	3000Mbps for 2.4Ghz / 5Ghz	1	YES	-	New one! In daily sales
HL-4GXV-F	4×10/100/1000	1	802.11ax 1800AX WiFi6	2x2 internal	1800Mbs for 2.4Ghz / 5Ghz	-	YES	-	In daily sales
HL-4GXVU-F	4×10/100/1000	1	802.11ax 1800AX WiFi6	2x2 internal	1800Mbs for 2.4Ghz / 5Ghz	-	YES	1	New one! In daily sales
HL-4BX3V-F	3×10/100/1000 1×2500	1	2T3R AX3000 WiFi6	2x3 Internal	3000Mbs for 2.4Ghz / 5Ghz	-	YES	-	New one! In daily sales
HL-4BY3V-F	1x100/1000/2500 3x10/100/1000	1	WIFI 7 Dual-Band 2.4Ghz/5Ghz	Internal	BE3600	-	YES	-	Coming soon!
HL-4BY7V-F	1x100/1000/2500 3x10/100/1000	1	WIFI 7 Dual-Band 2.4Ghz/5Ghz 4x4	Internal	BE7200	-	YES	-	Coming soon!
Fiber Tray for ONT based on CUBE housing
HL-FIBER-TRAY	-	-	-	-	-	-	-	-	In daily sales

Have a Question?

HALNy HLX-SFPX SFU Configuration [NOKIA 7360]

Service scenario

Supported SFU service scenario and ONT configuration

Credentials for web management

1. ONT Configuration (Access Mode – only INTERNET)

2. ONT Configuration (Access Mode – only IPTV)

3. ONT Configuration (Transparent Mode – INTERNET, VOIP, IPTV)

4. ONT Configuration (Vlan Translation – RBSA)

5. ONT Configuration (QinQ – INTERNET, VOIP, IPTV – unrestricted c-VLANs)

6. ONT Configuration (QinQ – INTERNET, VOIP, IPTV – restricted c-VLANs)

ONT HLX-SFPX upgrade on ISAM 7360