How Can We Help?

HL-1GE / HL-1GE2 SFU Configuration [ZYXEL]

You are here:
< All Topics
HL-2BV

HALNy HL-2BV Configuration

Service scenario

HL-1GE / HL-1GE2 can work in two modes – HGU (Home Gateway Unit) and SFU (Single Family Unit).
HGU mode configuration is presented here.
Managing ONT mode is done by setting up/or not bridge port and VEIP for ONT. In SFU mode we need to set bridge port and VEIP(only if we want to use ip-host).
SFU mode allows to prepare different configurations – such as QinQ tunnel or VLAN translation on the ONT. In this tutorial we will focus on SFU mode configuration.

ONT modes switching HGU<->SFU

Switching between HGU and SFU modes is described here.

Document Date and versionTested with ONT HALNy HL-1GE
Tested on ZYXEL OLT1404AVersion: V4.02(ABJB.3)C0_200904
Tested with ONT HALNy HL-1GE / HL-1GE2Supported on Version: V2.0.13 or above
Revision1
Let us know how to improve below document on: support@halny.com

Supported SFU service scenarios

1. ONT configuration (Access mode, only INTERNET)

ONT was connect to the GPON port 2 with ONU_ID 23

1. Create DBA-profile

OLT1404A(config)# qos bwprof 1G ustype 4 sir 0 air 0 pir 1024000

2. Authorize ONT – set correct serial number and password (register method A)

OLT1404A(config)# remote ont ont-2-23
OLT1404A(config-ont)# inactive
OLT1404A(config-ont)# sn 48414C4E206FD8B8
OLT1404A(config-ont)# password 00000001
OLT1404A(config-ont)# bwgroup 1 usbwprofname 1G dsbwprofname 1G
OLT1404A(config-ont)# ontWan 1
OLT1404A(config-ont-wan)# vlan 400
OLT1404A(config-ont-wan)# exit
OLT1404A(config-ont)# no inactive

3. Set uniport configuration

OLT1404A(config)# remote uniport uniport-2-23-1-1
OLT1404A(config-remote-veip-uniport)# queue tc 1 priority 0 weight 0 usbwprofname 1G dsbwprofname 1G dsoption olt bwsharegroupid 1
OLT1404A(config-remote-veip-uniport)# vlan 100 txtag untag ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# pvid 100
OLT1404A(config-remote-veip-uniport)# no inactive

4. Verify ONT ip-host 1 address

OLT1404A# show remote ont ont-2-23 ontWan-status
  -------------------------------------------------------------------------------------------------------
  Wan 1                                : Enable
  Connection Type                      : IPoE
  Status                               : Down
  Nat                                  : Disable
  Service                              :
  Default Wan                          : Disable
  Vlan                                 : 400
  Priority                             : 0
  Auto get IP                          : Disable
  IP address                           : 172.17.60.122
  IP Mask                              : 255.255.254.0
  Gateway                              : 172.17.60.1
  Primary DNS                          : 172.16.16.240
  Secondary DNS                        : 185.228.168.10
  Binding lan port                     :
  Binding wifi 2.4G ssid               : N/A
  Binding wifi 5G ssid                 : N/A
  -------------------------------------------------------------------------------------------------------

2. ONT configuration (Access mode, only IPTV)

ONT was connect to the GPON port 2 with ONU_ID 24

1. Create DBA-profile

OLT1404A(config)# qos bwprof 1G ustype 4 sir 0 air 0 pir 1024000

2. Authorize ONT – set correct serial number and password (register method A)

OLT1404A(config)# remote ont ont-2-24
OLT1404A(config-ont)# inactive
OLT1404A(config-ont)# sn 48414C4E206FD8B8
OLT1404A(config-ont)# password 00000001
OLT1404A(config-ont)# bwgroup 1 usbwprofname 1G dsbwprofname 1G
OLT1404A(config-ont)# ontWan 1
OLT1404A(config-ont-wan)# vlan 400
OLT1404A(config-ont-wan)# exit
OLT1404A(config-ont)# no inactive

3. Set uniport configuration

OLT1404A(config)# remote uniport uniport-2-24-1-1
OLT1404A(config-remote-veip-uniport)# queue tc 1 priority 0 weight 0 usbwprofname 1G dsbwprofname 1G dsoption olt bwsharegroupid 1
OLT1404A(config-remote-veip-uniport)# vlan 200 txtag untag ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# pvid 200
OLT1404A(config-remote-veip-uniport)# igmpchannel 200 txtag transparent
OLT1404A(config-remote-veip-uniport)# no inactive

4. Verify ONT ip-host 1 address

OLT1404A# show remote ont ont-2-24 ontWan-status
  -------------------------------------------------------------------------------------------------------
  Wan 1                                : Enable
  Connection Type                      : IPoE
  Status                               : Down
  Nat                                  : Disable
  Service                              :
  Default Wan                          : Disable
  Vlan                                 : 400
  Priority                             : 0
  Auto get IP                          : Disable
  IP address                           : 172.17.60.122
  IP Mask                              : 255.255.254.0
  Gateway                              : 172.17.60.1
  Primary DNS                          : 172.16.16.240
  Secondary DNS                        : 185.228.168.10
  Binding lan port                     :
  Binding wifi 2.4G ssid               : N/A
  Binding wifi 5G ssid                 : N/A
  -------------------------------------------------------------------------------------------------------

3. ONT configuration (TRANSPARENT mode)

ONT was connect to the GPON port 2 with ONU_ID 25

1. Create DBA-profile

OLT1404A(config)# qos bwprof 1G ustype 4 sir 0 air 0 pir 1024000

2. Authorize ONT – set correct serial number and password (register method A)

OLT1404A(config)# remote ont ont-2-25
OLT1404A(config-ont)# inactive
OLT1404A(config-ont)# sn 48414C4E206FD8B8
OLT1404A(config-ont)# password 00000001
OLT1404A(config-ont)# bwgroup 1 usbwprofname 1G dsbwprofname 1G
OLT1404A(config-ont)# host-ip vlan 400
OLT1404A(config-ont)# no inactive

3. Set uniport configuration

OLT1404A(config)# remote uniport uniport-2-25-1-1
OLT1404A(config-remote-veip-uniport)# queue tc 1 priority 0 weight 0 usbwprofname 1G dsbwprofname 1G dsoption olt bwsharegroupid 1
OLT1404A(config-remote-veip-uniport)# vlan 100 ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# vlan 200 ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# vlan 300 ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# igmpchannel 200 txtag transparent
OLT1404A(config-remote-veip-uniport)# no inactive

4. Verify ONT ip-host 1 address

OLT1404A# show remote ont ont-2-25 ontWan-status
  -------------------------------------------------------------------------------------------------------
  Wan 1                                : Enable
  Connection Type                      : IPoE
  Status                               : Down
  Nat                                  : Disable
  Service                              :
  Default Wan                          : Disable
  Vlan                                 : 400
  Priority                             : 0
  Auto get IP                          : Disable
  IP address                           : 172.17.60.122
  IP Mask                              : 255.255.254.0
  Gateway                              : 172.17.60.1
  Primary DNS                          : 172.16.16.240
  Secondary DNS                        : 185.228.168.10
  Binding lan port                     :
  Binding wifi 2.4G ssid               : N/A
  Binding wifi 5G ssid                 : N/A
  -------------------------------------------------------------------------------------------------------

4. ONT configuration (Hybrid mode)

ONT was connect to the GPON port 2 with ONU_ID 26

1. Create DBA-profile

OLT1404A(config)# qos bwprof 1G ustype 4 sir 0 air 0 pir 1024000

2. Authorize ONT – set correct serial number and password (register method A)

OLT1404A(config)# remote ont ont-2-26
OLT1404A(config-ont)# inactive
OLT1404A(config-ont)# sn 48414C4E206FD8B8
OLT1404A(config-ont)# password 00000001
OLT1404A(config-ont)# bwgroup 1 usbwprofname 1G dsbwprofname 1G
OLT1404A(config-ont)# host-ip vlan 400
OLT1404A(config-ont)# no inactive

3. Set uniport configuration

OLT1404A(config)# remote uniport uniport-2-26-1-1
OLT1404A(config-remote-veip-uniport)# queue tc 1 priority 0 weight 0 usbwprofname 1G dsbwprofname 1G dsoption olt bwsharegroupid 1
OLT1404A(config-remote-veip-uniport)# vlan 100 txtag untag ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# vlan 200 ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# pvid 100
OLT1404A(config-remote-veip-uniport)# igmpchannel 200 txtag transparent
OLT1404A(config-remote-veip-uniport)# no inactive

4. Verify ONT ip-host 1 address

OLT1404A# show remote ont ont-2-26 ontWan-status
  -------------------------------------------------------------------------------------------------------
  Wan 1                                : Enable
  Connection Type                      : IPoE
  Status                               : Down
  Nat                                  : Disable
  Service                              :
  Default Wan                          : Disable
  Vlan                                 : 400
  Priority                             : 0
  Auto get IP                          : Disable
  IP address                           : 172.17.60.122
  IP Mask                              : 255.255.254.0
  Gateway                              : 172.17.60.1
  Primary DNS                          : 172.16.16.240
  Secondary DNS                        : 185.228.168.10
  Binding lan port                     :
  Binding wifi 2.4G ssid               : N/A
  Binding wifi 5G ssid                 : N/A
  -------------------------------------------------------------------------------------------------------

5. ONT configuration (VLAN translation – rBSA)

ONT was connect to the GPON port 2 with ONU_ID 27

1. Create DBA-profile

OLT1404A(config)# qos bwprof 1G ustype 4 sir 0 air 0 pir 1024000

2. Authorize ONT – set correct serial number and password (register method A)

OLT1404A(config)# remote ont ont-2-27
OLT1404A(config-ont)# inactive
OLT1404A(config-ont)# sn 48414C4E206FD8B8
OLT1404A(config-ont)# password 00000001
OLT1404A(config-ont)# bwgroup 1 usbwprofname 1G dsbwprofname 1G
OLT1404A(config-ont)# host-ip vlan 400
OLT1404A(config-ont)# no inactive

3. Set uniport configuration

OLT1404A(config)# remote uniport uniport-2-27-1-1
OLT1404A(config-remote-veip-uniport)# queue tc 1 priority 0 weight 0 usbwprofname 1G dsbwprofname 1G dsoption olt bwsharegroupid 1
OLT1404A(config-remote-veip-uniport)# vlan 35 network 100 ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# vlan 838 network 200 ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# vlan 839 network 300 ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# igmpchannel 838 txtag transparent
OLT1404A(config-remote-veip-uniport)# no inactive

4. Verify ONT ip-host 1 address

OLT1404A# show remote ont ont-2-27 ontWan-status
  -------------------------------------------------------------------------------------------------------
  Wan 1                                : Enable
  Connection Type                      : IPoE
  Status                               : Down
  Nat                                  : Disable
  Service                              :
  Default Wan                          : Disable
  Vlan                                 : 400
  Priority                             : 0
  Auto get IP                          : Disable
  IP address                           : 172.17.60.122
  IP Mask                              : 255.255.254.0
  Gateway                              : 172.17.60.1
  Primary DNS                          : 172.16.16.240
  Secondary DNS                        : 185.228.168.10
  Binding lan port                     :
  Binding wifi 2.4G ssid               : N/A
  Binding wifi 5G ssid                 : N/A
  -------------------------------------------------------------------------------------------------------

6. ONT configuration (802.1q in 802.1q Begin/End of Tunnel)

ONT was connect to the GPON port 2 with ONU_ID 28

1. Create DBA-profile

OLT1404A(config)# qos bwprof 1G ustype 4 sir 0 air 0 pir 1024000

2. Authorize ONT – set correct serial number and password (register method A)

OLT1404A(config)# remote ont ont-2-28
OLT1404A(config-ont)# inactive
OLT1404A(config-ont)# sn 48414C4E206FD8B8
OLT1404A(config-ont)# password 00000001
OLT1404A(config-ont)# bwgroup 1 usbwprofname 1G dsbwprofname 1G
OLT1404A(config-ont)# host-ip vlan 400
OLT1404A(config-ont)# no inactive

3. Set uniport configuration

OLT1404A(config)# remote uniport uniport-2-28-1-1
OLT1404A(config-remote-veip-uniport)# queue tc 1 priority 0 weight 0 usbwprofname 1G dsbwprofname 1G dsoption olt bwsharegroupid 1
OLT1404A(config-remote-veip-uniport)# vlan all network 999:all ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# no inactive

4. Verify ONT ip-host 1 address

OLT1404A# show remote ont ont-2-28 ontWan-status
  -------------------------------------------------------------------------------------------------------
  Wan 1                                : Enable
  Connection Type                      : IPoE
  Status                               : Down
  Nat                                  : Disable
  Service                              :
  Default Wan                          : Disable
  Vlan                                 : 400
  Priority                             : 0
  Auto get IP                          : Disable
  IP address                           : 172.17.60.122
  IP Mask                              : 255.255.254.0
  Gateway                              : 172.17.60.1
  Primary DNS                          : 172.16.16.240
  Secondary DNS                        : 185.228.168.10
  Binding lan port                     :
  Binding wifi 2.4G ssid               : N/A
  Binding wifi 5G ssid                 : N/A
  -------------------------------------------------------------------------------------------------------

7. ONT configuration (OSE / MdO)

ONT was connect to the GPON port 2 with ONU_ID 29

1. Create DBA-profile

OLT1404A(config)# qos bwprof 1G ustype 4 sir 0 air 0 pir 1024000

2. Authorize ONT – set correct serial number and password (register method A)

OLT1404A(config)# remote ont ont-2-29
OLT1404A(config-ont)# inactive
OLT1404A(config-ont)# sn 48414C4E206FD8B8
OLT1404A(config-ont)# password 00000001
OLT1404A(config-ont)# bwgroup 1 usbwprofname 1G dsbwprofname 1G
OLT1404A(config-ont)# host-ip vlan 400
OLT1404A(config-ont)# no inactive

3. Set uniport configuration

OLT1404A(config)# remote uniport uniport-2-29-1-1
OLT1404A(config-remote-veip-uniport)# queue tc 1 priority 0 weight 0 usbwprofname 1G dsbwprofname 1G dsoption olt bwsharegroupid 1
OLT1404A(config-remote-veip-uniport)# vlan 10 network 999:100 ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# vlan 11 network 999:200 ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# vlan 12 network 999:300 ingprof DEFVAL
OLT1404A(config-remote-veip-uniport)# no inactive

4. Verify ONT ip-host 1 address

OLT1404A# show remote ont ont-2-29 ontWan-status
  -------------------------------------------------------------------------------------------------------
  Wan 1                                : Enable
  Connection Type                      : IPoE
  Status                               : Down
  Nat                                  : Disable
  Service                              :
  Default Wan                          : Disable
  Vlan                                 : 400
  Priority                             : 0
  Auto get IP                          : Disable
  IP address                           : 172.17.60.122
  IP Mask                              : 255.255.254.0
  Gateway                              : 172.17.60.1
  Primary DNS                          : 172.16.16.240
  Secondary DNS                        : 185.228.168.10
  Binding lan port                     :
  Binding wifi 2.4G ssid               : N/A
  Binding wifi 5G ssid                 : N/A
  -------------------------------------------------------------------------------------------------------

ONT HL-1GE / HL-1GE2 SFU upgrade on ZYXEL OLT1404A/OLT1408A

HL-1GE / HL-1GE2 can be upgrade the same way as other HALNy ONTs, You can find upgrade procedure here.


Table of Contents